| File size: | 417.00 MB |
| Released: | Mar 22, 2016 |
| Downloads: | Total: 86 | This Week: 0 |
| Tags: |
- The D5 and D500 ISO sensitivity displays are now supported. If you are using two WR-1 units, one as a receiver and the other as a transmitter, update both to firmware version 1.01.
- When used as a transmitter to change ISO sensitivity for a receiving camera, the WR-1 no longer cycles continuously through the available values.
- D5, D4S, D4, Df, D810A, D810, D800, D800E, D750, D500, D7200, and D7100 cameras
- Other cameras cannot be used to upgrade WR-1 firmware.
On the Camera
- Attach the WR-1 to the camera and slide the Tx/Rx/OFF switch to Rx.
- Turn the camera on.
- Press the camera MENU button and select Firmware version in the SETUP MENU.
- Check the WR-1 firmware version (“W”).
- Turn the camera off.
On the WR-1
- Slide the Tx/Rx/OFF switch to Tx or Rx.
- Press MENU and highlight VERSION using the multi selector.
- Check the firmware version.
- Slide the Tx/Rx/OFF switch to OFF.
- Create a folder on the computer hard disk and name it as desired.
- Download the file to the folder created.
- Run the package to extract the following folder named “WR1Update”.
- Using a card slot or card reader, copy the .bin file to a memory card that has been formatted in the camera.
- After attaching the WR-1, insert the memory card into Slot 1 on the camera, turn the camera on, and slide the WR-1 Tx/Rx/OFF switch to Rx.
- Select Firmware version in the SETUP MENU and follow the on-screen instructions to complete the firmware update.
- Once the update is complete, turn the camera off and remove the memory card.
- Confirm that the firmware has been updated to the new version.
Updating to a different firmware version than the one already installed on the adapter can bring various changes such as improved performance and stability, add new features or enhance existing ones, but also various fixes for more or less recurrent issues.
Given the large variety of camera adapters and numerous methods for upgrading the device, it is highly recommended that you read and, above all, understand the installation steps before you consider applying the new firmware, even if you are a power user.
If you try to perform the update without knowing all the steps, you risk ending up with a broken device. However, what every upgrade needs is a compatible firmware to be transferred to the adapter (or to the camera) via either a USB cable or a suitable memory card.
That being said, if you consider applying this release and have made sure you’re properly informed on the process of performing the upgrade successfully, hit the download button, and update your camera adapter.
Check with our website as often as possible in order to be up to date with the latest releases.
Use the Wireless Transmitter Utility to adjust network settings and the like for WT-7, WT-6, WT-5, and WT-4 wireless transmitters, UT-1 communications units, and cameras with built-in Wi-Fi and/or Ethernet. The software for the WT-4 was called the WT-4 Setup Utility, but now that it supports the WT-5 and other devices ...
Changes: - Fixed an issue that prevented additional deletions after multiple shots had been deleted in succession from a single burst of pictures. Confirming the firmware version - Turn on the camera. - Press the camera’s MENU button and select Firmware version from the setup menu. - The ...
Changes:- Fixed an issue that caused the display to flicker if pictures were scrolled during playback zoom after the user had taken pictures using the viewfinder with Prioritize viewfinder selected for monitor mode and then removed his or her eye from the viewfinder before starting playback. - Fixed an issue that ...
New Features: - The WT-7 wireless transmitter is now supported. Fixed the following issues: - Multiple exposures were not recorded correctly. - Incorrect histograms would be displayed for some images viewed in the RGB histogram display during playback. - If On was selected for Auto distortion control, distortion ...
Fixed the following issues:- Waking the camera by pressing a control such as the AF-ON button after the standby timer had expired would in very rare instances cause camera settings to change or shooting would to start without the shutter-release button being pressed. - The shutter release would in very rare ...
Changes:- When users attempted to pair the camera with the smart device using the SnapBridge app under iOS 13, pairing would end in failure and a message to that effect would be displayed. Viewing the Camera Firmware Version: - Turn the camera on. - Press the camera MENU button to ...
Recall shooting functions:- Added Recall shooting functions to the functions that can be assigned to camera controls. Holding the selected control recalls previously-saved exposure settings (including shutter speed and aperture), a feature that can for example be used to switch rapidly between scenes that require different exposures. - Recall shooting ...
Changes:- The SETUP MENU > Time zone and date > Time zone display now shows only the names of major cities in the currently selected zone.Viewing the Camera Firmware Version: - Turn the camera on. - Press the camera MENU button and select Firmware version in the SETUP MENU to ...
This package contains the files needed for installing the Wireless Transmitter utility to adjust network settings. If your computer is currently running an older version of this utility, updating may fix problems, add new functions, or expand existing ones. Even though other OSes might be compatible, we do not recommend applying ...
NX Tether software is designed for tethered photography with Nikon cameras connected to your computer. NX Tether can be used to adjust camera settings from and download pictures to the computer, where it can link with other software such as NX Studio. A simple, stripped-down design combined with an uncluttered, intuitive ...