| File size: | 33.50 MB |
| Released: | Jun 8, 2016 |
| Downloads: | Total: 75 | This Week: 1 |
| Tags: |
- Fixed an issue that occurred with WR-R10 wireless remote controller firmware version 3.00. In rare cases, the camera would fail to display the number of exposures remaining or would take about a minute to power down when the WR-R10 was connected.
- Turn the camera on.
- Press the camera MENU button and select Firmware version in the SETUP MENU to display the camera firmware version.
- Check the camera firmware version.
- Turn the camera off.
- Download and run the file.
- Using a card slot or card reader, copy the .bin to a memory card that has been formatted in the camera.
- Insert the memory card into the primary slot on the camera and turn the camera on.
- Select Network in the SETUP MENU and confirm that Disable is selected for Network connection.
- Select Firmware version in the SETUP MENU and follow the on-screen instructions to complete the firmware update.
- Once the update is complete, turn the camera off and remove the memory card.
- Confirm that the firmware has been updated to the new version.
Updating to a newer firmware version than the one already installed on your camera can improve the device’s overall performance and stability, resolve various issues, and add support for newly developed features or enhance existing ones.
On the other hand, downgrading the camera’s firmware can recover its functionality in the unlikely event the currently installed version is faulty or the device’s performance dropped after an upgrade. However, bear in mind that applying an earlier build might not always be possible.
It is recommended that changing the camera’s firmware be performed when the new release resolves an issue that your device has been encountering, or adds a new feature (or enhances an existing one) that could prove useful for you.
This process isn’t intended to be destructive, but still, it’s best to save all your personal data and configurations before applying a different firmware. Moreover, make sure that the battery is fully charged and don’t use the camera’s buttons while the installation is in progress.
When it comes to the update method, usually, you must copy the firmware file onto a compatible memory card, insert it into the camera, and browse from the menu to the device’s update section.
However, each device has various ways to enter the update mode and particular steps that should be taken for a successful upgrade, therefore make sure you read the product’s installation guide.
That being said, if you consider that this firmware improves your device in any way, then hit the download button and get the desired version; if not, check with our website as often as possible so that you don’t miss the update that will boost your camera’s performance.
It is highly recommended to always use the most recent driver version available
Do not forget to check with our site as often as possible in order to stay updated on the latest drivers, software and games
Try to set a system restore point before installing a device driver
This will help if you installed a wrong driver
Problems can arise when your hardware device is too old or not supported any longer
Changes:- Fixed an issue that caused the display to flicker if pictures were scrolled during playback zoom after the user had taken pictures using the viewfinder with Prioritize viewfinder selected for monitor mode and then removed his or her eye from the viewfinder before starting playback. - Fixed an issue that ...
Use the Wireless Transmitter Utility to adjust network settings and the like for WT-7, WT-6, WT-5, and WT-4 wireless transmitters, UT-1 communications units, and cameras with built-in Wi-Fi and/or Ethernet. The software for the WT-4 was called the WT-4 Setup Utility, but now that it supports the WT-5 and other devices ...
Changes: - Fixed an issue that sometimes resulted in incorrect exposure for the first photo taken in live view. Viewing the Camera Firmware Version: - Turn the camera on. - Press the camera MENU button and select Firmware version in the SETUP MENU to display the camera firmware version. ...
Use the Wireless Transmitter Utility to adjust network settings and the like for WT-7, WT-6, WT-5, and WT-4 wireless transmitters, UT-1 communications units, and cameras with built-in Wi-Fi and/or Ethernet. The software for the WT-4 was called the WT-4 Setup Utility, but now that it supports the WT-5 and other devices ...
Changes: - Fixed an issue that prevented additional deletions after multiple shots had been deleted in succession from a single burst of pictures. Confirming the firmware version - Turn on the camera. - Press the camera’s MENU button and select Firmware version from the setup menu. - The ...
NX Studio software offers a full-fledged suite of intuitive tools for viewing, processing, and editing photos and videos. It combines the photo-and-video-viewing features of ViewNX-i with the photo-processing and retouch tools of Capture NX-D in a single, comprehensive workflow. Not only can it be used to process RAW pictures, ...
Changes:- Added support for the Z 9. When used with the Z 9, the product supports display and selection of shutter speeds as fast as 1/32,000. WR-1 firmware updates can be performed with:- Z 9, Z 7II, Z 7, Z 6II, Z 6, and Z 5 cameras - D6, D5, D4S, ...
Picture Control Utility 2 is used to edit and manage Picture Controls. Starting from NEF (RAW) images or custom Picture Controls copied from a camera, you can create and save new custom Picture Controls. Custom Picture Controls created in Picture Control Utility 2 can be used with NX Studio or Camera ...
NX Tether software is designed for tethered photography with Nikon cameras connected to your computer. NX Tether can be used to adjust camera settings from and download pictures to the computer, where it can link with other software such as NX Studio. A simple, stripped-down design combined with an ...
NX Studio software offers a full-fledged suite of intuitive tools for viewing, processing, and editing photos and videos. It combines the photo-and-video-viewing features of ViewNX-i with the photo-processing and retouch tools of Capture NX-D in a single, comprehensive workflow. Not only can it be used to process RAW pictures, but ...