Sony ILCE-7SM2 Camera Firmware 2.1

Details

File size: 238.60 MB
Released: Apr 28, 2016
Downloads: Total: 126 | This Week: 0
Tags:

Sony ILCE-7SM2 Camera Firmware 2.1 - Description

This package provides the necessary installation files of Sony ILCE-7SM2 Camera Firmware 2.1.

Improvements:

- Allows the camera to record XAVCS format video with an SDHC card in addition to SDXC card.

Notes:

- When an SDHC memory card is used to record movies in XAVC S format over extended periods of time, the recorded movies will be divided into files of 4 GB, and the divided files can then be integrated into a single file using the PlayMemories Home software
- Shooting movies in XAVC S format requires SD Speed Class 10, UHS Speed Class U1, or faster
- When recording at 100 Mbps or more, UHS Speed Class U3 is required

Download and Update the Firmware:

- IMPORTANT: Do not allow the computer to enter Sleep (Standby) mode during the update process.
- Download the firmware file to a temporary or download directory.
- Go to the directory where the file was downloaded and double-click the downloaded file to begin the Firmware Updater.
- Connect the camera to your computer using the supplied USB cable.
- The LCD screen on the camera will turn off when it is connected to the computer. If the LCD screen of camera does not turn off, disconnect and reconnect the USB cable to the camera. If the computer has additional USB ports, try connecting the USB cable to different USB port.
- Verify that the Remove Hardware icon or is displayed in the task tray at the lower right-hand corner of the computer screen.
- At the Firmware Updater screen, click Next.
- Do not power off the camera or disconnect the USB cable until the update process is complete.
- When the next screen is displayed, check the version number at the lower left and click Next.
- When the next screen is displayed, click the Remove Hardware icon or in the task tray to stop the USB connection. If the Remove Hardware icon is not displayed on the task tray, please proceed to the next step.
- Do not disconnect the USB cable from the camera or the computer.
- On the camera, press the center button of the Control Wheel to reset the camera.
- When the next screen is displayed, click Run.
- Do not power off the camera or disconnect the USB cable until the update process is complete.
- The update process takes about fifteen minutes to complete.
- After clicking Finish, make sure to wait for the camera screen to turn back on before you continue, this may take a few minutes.
- Click the Remove Hardware icon or in the task tray to stop the USB connection, and then disconnect the USB cable.
- Power off the camera, then remove the battery pack or AC adapter.
- Reconnect the battery pack or AC adapter and power on the camera.

About Digital Camera Updates:

Updating to a newer firmware version than the one already installed on your camera can improve the device’s overall performance and stability, resolve various issues, and add support for newly developed features or enhance existing ones.

On the other hand, downgrading the camera’s firmware can recover its functionality in the unlikely event the currently installed version is faulty or the device’s performance dropped after an upgrade. However, bear in mind that applying an earlier build might not always be possible.

It is recommended that changing the camera’s firmware be performed when the new release resolves an issue that your device has been encountering, or adds a new feature (or enhances an existing one) that could prove useful for you.

This process isn’t intended to be destructive, but still, it’s best to save all your personal data and configurations before applying a different firmware. Moreover, make sure that the battery is fully charged and don’t use the camera’s buttons while the installation is in progress.

When it comes to the update method, usually, you must copy the firmware file onto a compatible memory card, insert it into the camera, and browse from the menu to the device’s update section.

However, each device has various ways to enter the update mode and particular steps that should be taken for a successful upgrade, therefore make sure you read the product’s installation guide.

That being said, if you consider that this firmware improves your device in any way, then hit the download button and get the desired version; if not, check with our website as often as possible so that you don’t miss the update that will boost your camera’s performance. 

Windows 10 Sony ILCE-7SM2 Camera Firmware 2.1 related drivers

Sony Alpha DSLR-A100 Camera Firmware 1.04

This utility updates the camera firmware to version 1.04 and provides the following benefits: Improvements over firmware version 1.02:- Adds support for the camera to display focal length information about an attached Zoom Lens DT 55-200mm F4-5.6. Additional improvements over original firmware:- Addresses the symptom where, in very rare cases, RAW ...

Sony Alpha DSLR-A330 Camera Firmware 1.10

This utility updates the DSLR-A330 firmware to version 1.10 and improves the operability of the AE (Auto Exposure) lock function. After updating the firmware, the exposure will be locked when the shutter button is pressed half way down when shooting with the metering mode set to either Spot or Center Weighted.IMPORTANT: ...

Sony Alpha DSLR-A700K Camera Firmware 1.10

This utility updates the DSLR-A700 Camera Firmware to version 4 and provides the following benefits: Benefits over firmware version 3:- Adds a "2 steps/3 shots" option to the "Bracket: Single" and "Bracket: Cont." Drive mode settings for auto exposure bracketing. - Adds an "Off" option to the "High ISO NR" (Noise ...

Sony ILCE-7 Camera Firmware 3.10

Fixes: - Phase-detection AF is supported - The lens name will be correctly recorded in the EXIF - The AF can be used in movie recording mode with the SEL85F14GM Download and Update the Firmware: - IMPORTANT: Do not allow the computer to enter Sleep (Standby) mode during the ...

Sony ILCE-7RM2 Camera Firmware 3.10

Fixes: - Phase-detection AF is supported - The AF can be used in movie recording mode with the SEL85F14GM Download and Update the Firmware: - IMPORTANT: Do not allow the computer to enter Sleep (Standby) mode during the update process. - Download the firmware file to a temporary or download ...

Sony Alpha DSLR-A700 Camera Firmware 1.10

This utility updates the DSLR-A700 Camera Firmware to version 4 and provides the following benefits: Benefits over firmware version 3:- Adds a "2 steps/3 shots" option to the "Bracket: Single" and "Bracket: Cont." Drive mode settings for auto exposure bracketing. - Adds an "Off" option to the "High ISO NR" (Noise ...

Sony ILCE-7RM2 Camera Firmware 3.30

Improvements: - Adds support for Radio Controlled Lighting System - Improves stability in picture shooting mode (optimizing temperature control, effect is different according to temperature) - Adds support to output video via HDMI (still mode) when using the Remote Camera Control software - Improves overall stability and operability of the ...

Sony DSC-RX100M5 Camera Firmware 1.01

Check the version of your camera firmware: - Power on the camera. - Press the Menu button. - At the Menu screen, use the Control Wheel to select Setup, and then select Version. - The firmware version is displayed on the LCD screen. - If the current firmware version is 1.01 ...

Sony ILCE-6000 Camera Firmware 3.10

Fixes: - Phase-detection AF is supported - The lens name will be correctly recorded in the EXIF - The AF can be used in movie recording mode with the SEL85F14GM Download and Update the Firmware: - IMPORTANT: Do not allow the computer to enter Sleep (Standby) mode during the ...

Sony ILCE-7M2 Camera Firmware 3.10

Fixes: - Phase-detection AF is supported - The lens name will be correctly recorded in the EXIF - The AF can be used in movie recording mode with the SEL85F14GM Download and Update the Firmware: - IMPORTANT: Do not allow the computer to enter Sleep (Standby) mode during the ...